A beadboard cathedral ceiling is a practical way to add architectural character, texture, and warmth to a sloped interior ceiling. Beadboard can also cover popcorn ceilings, textured paint, cracks, dents, and uneven plaster without the long, messy process of removing the existing finish.
Beadboard is wood paneling with long, continuous vertical grooves and raised beads that create the illusion of multiple panels of wood. A cathedral ceiling can be finished with painted or stained wood beadboard, PVC panels, styrofoam panels, or other lightweight systems, depending on the room, the ceiling condition, the desired appearance, and the installation method.

What Is a Beadboard Cathedral Ceiling?
A beadboard ceiling is an interior roof of a commercial or residential property that uses a set of ceiling beadboard panels to produce a practical and visually appealing finish. Beadboard for ceilings can be used to mask unsightly blemishes and outdated finishing materials with a fresh and easily-maintained surface that also provides a little extra heat and noise insulation.
Beadboard is a timeless style of wall and ceiling paneling that uses vertical strips of material and indented, or beaded, overlaps to provide a protective and visually distinct finish to tired and worn surfaces. Traditionally, beadboard panels were formed from long and thin strips of heavy wood, but modern beadboard ceiling panels can be made from a variety of materials.
Not only can beadboard be used for ceilings, but it's actually a really popular and beautiful use of this material. Taking up most of the surface area of any room, your ceilings should never be overlooked and fortunately, due to beadboard being lightweight, it's not a challenge to install it overhead.
Why Use Beadboard on a Cathedral Ceiling?
Beadboard ceilings look refined and professional, offering an air of nautical chic to any style of home. For this reason, it’s no surprise that this trend has taken the internet by storm. From Instagram and Pinterest to TikTok, homeowners are obsessed with the #accentceiling aesthetic and beadboard ceilings are among the most popular.
Choosing to install a beadboard panel ceiling can bring about a number of brilliant benefits for home and business owners. Not only can the visual appearance of beadboard on ceilings evoke the homely and welcoming aesthetics of a traditional New England cottage, it can also offer a cost-effective, easily-installed and simple-to-maintain alternative to plaster and paints.
Beadboard ceiling panels are, by design, incredibly easy to install regardless of whether you have any previous DIY experience. Due to the lightweight nature of PVC and styrofoam tiles, they can be secured directly to existing ceiling foundations using any standard tile adhesive, enabling you to produce professional and eye-catching installations in only an hour or two.
Covering an Existing Popcorn or Textured Ceiling
One of the most popular uses of beadboard ceiling panels is to cover outdated or unsightly installations like textured paint and popcorn ceilings. The latter of these can be particularly tricky, as removing popcorn ceilings is not only messy, it can also be harmful to your health.
Scraping off a popcorn ceiling releases fine particles into the air that can cause health issues if inhaled, especially if the installation pre-dates the 1991 ban on asbestos in construction. To be safe, just install beadboard ceiling panels directly to the ceiling using the process outlined above, or consider hiring tradespeople to install a drop ceiling from which to hang your tiles.
We knew the removal would be super messy so we opted to cover the ceiling instead. I love the way it turned out.
Choosing the Right Beadboard Material
Depending on what kind of effect you’re aiming for, you can choose the size and material beadboard that works for you. You can go for pine, MDF or whatever wood fits your desired aesthetic.
Modern beadboard ceiling panels can be made from a variety of materials. For example, we currently stock both PVC and styrofoam beadboard ceiling panels in a wide range of colors and designs.
The benefit being that individual panels can be easily installed in the same way as a standard set of decorative tiles, removing the cumbersome aspects of handling heavy panels and providing the durability and upkeep benefits of modern materials.
Wood Beadboard
Stained or painted wood Beadboard is perfectly fine for covered porch ceilings providing the roof above does not leak. More recently it has become popular to stain wood beadboard porch ceilings.
Pine yellows over time even when covered by white paint, so this is something to keep in mind if you’re happy to spend a little more for it to be low maintenance down the line.
Individual boards can also be shimmed with thin strips of wood to smooth out any unevenness in underlying ceiling joists. This can be done as you proceed, something that is very difficult to do with 4x8 sheet material.
PVC and Styrofoam Beadboard
High durability and low maintenance PVC beadboard ceiling panels, unlike many wooden and metal materials, are both fire and water-resistant, while also being less prone to cosmetic damages like scratches and fading.
You can also worry less about pest infestations, as PVC and styrofoam beadboard ceiling panels are far more resistant to insects and critters than traditional wood beadboard planks.
Like other types of PVC ceiling tiles, beadboard ceiling panels are incredibly easy to clean and maintain. If any dust or dirt does take hold, you can simply wipe your panels down with a damp cloth and they’ll look good as new.
Tongue-and-Groove Boards or Large Sheets
Tongue & Groove Beadboard is Far Superior to 4x8 Sheets. Installing 4x8 sheets of fake beadboard paneling may seem like a good idea . until they've been up a few months. Then the wavy, sagging panels will look even worse than the plywood you're probably trying to hide.
Far better to use our genuine, traditional wood tongue & groove beadboard and do the job right the first time! (Our PVC tongue & groove beadboard also works great.)
Because you're working with individual boards rather than awkwardly large and floppy sheets, installation will also be much easier.
4x8 sheets of beadboard are much larger than standard 20”x20” beadboard ceiling panels, so your installation process may need to be adjusted slightly. As these types of panels are much heavier, it’s advisable to consider nailing up the perimeters alongside adding standard tile adhesive to the body of each panel, this helps ensure a secure and smooth installation.
You should also have a couple of people with you to help lift and affix these types of panels to your ceiling, as the added size and weight can make performing a solo installation a little dangerous.
| Material or format | Important characteristics |
|---|---|
| Wood beadboard | Natural character, warmth, and the option to stain or paint |
| PVC beadboard | Fire and water-resistant, easy to clean, and resistant to scratches, fading, insects, and critters |
| Styrofoam beadboard | Lightweight and suitable for adhesive installation |
| Tongue & groove boards | Individual boards are easier to handle and can be shimmed to correct unevenness |
| 4x8 sheets | Large and heavier, requiring additional support and several people for installation |
Beadboard Ceiling Cost
Beadboard ceilings don’t have to be expensive. The typical cost of materials and labor are between $4.00 and $7.00 per square foot.
The cost can go up considerably if you use more expensive wood panels. Some cost as much as $40.00 per square foot. Labor costs can also go up if you have an odd shaped asymmetrical ceiling or a lot of ceiling fixtures to work around.
Finishing any large surface in a home or business to a professional standard will always be fairly expensive, but choosing to install beadboard ceiling panels can offset some significant costs.
Not only are the tiles themselves pretty affordable, but due to their lightweight design and glue up installation requirements, they can be easily installed by any avid DIY-er.
Design Ideas for a Beadboard Cathedral Ceiling
White Beadboard for a Bright, Refined Look
Whitewashed beadboard ceilings for a beach-house yet refined living room. If you're dealing with a small room on a budget, beadboard ceilings with a gentle whitewash paint will immediately give your space an easy-living, chilled out look of coastal calm.
From here, we suggest sticking to a cool colour scheme for a refreshing, Scandi twist. The architectural detail of the whitewashed beadboard ceilings, paired with the light colours elsewhere will create a feeling of spaciousness and intentional simplicity.
Blue or Teal Beadboard for a Sky-Like Effect
Colourful beadboard ceilings are the ultimate design statement, promising to draw the eye upwards and give a room vitality and character. Blue beadboard is an especially clever interior design trick, creating the illusion of blue skies and cultivating a sense of space.
The best thing about blue? It's one of those colours that can lend itself to a bright and quirky colour palette or an earthy, neutral look.
Traditionally, porch ceilings were painted light blue. Although we do not know for sure, here are two theories we have heard:
- Blue reminds people of the sky above.
- Blue helps keep mosquitoes away.
Rustic Wood with Stone or Brick
We love the cozy, cabin-esque retreat feel that can be created using natural wooden beadboard ceilings. Using simple, pine beadboard overhead and oversized grey stone on the walls, The Porch Company has cultivated a warm, chalet-style charm in this home.
If your style is traditional and rustic, timber beadboard ceilings are a fantastic way to offer natural character and warmth. We love the idea of installing wooden beadboard in a family room or games room in need of some soul.
There's no denying exposed brick is a trend that is here to stay. So, why not give it a stylish twist with some white beadboard ceilings? The way that red brick contrasts with white beadboard gives a fresh yet natural look in this project by Georgia Zikas Design.
Beadboard in a Contemporary Kitchen
While we love beadboard for the coastal, country, rustic charm it can bring to our interiors - we also love adding beadboard ceilings as an accent in more contemporary spaces.
This kitchen shows how you can combine materials to give space, texture and depth. White marble kitchen tops, a metallic caged pendant light, wooden floors and a beadboard ceiling accent? Who knew you could give a functional space so much character without indulging in prints and colourful paint? (Us beadboard advocates did!)
Partial Beadboard for a Loft Hatch or Accent Area
Want some beadboard overhead but don't want to commit to covering the entire ceiling? Simply cut your beadboard down to size and stick it to your loft hatch.
Not only does this trick add depth by drawing the eye towards the detail, it also offers some elegant intrigue to an otherwise neutral space. Beadboard and other wall panelling techniques are a great way to introduce texture to interiors that champion minimalist colour palettes.
Herringbone and Beam-Based Layouts
We used our own Vintage Woodworks Beadboard on the porch ceiling of one of our office buildings . and we love it! The 3-1/4" wide Yellow Pine Beadboard was installed in a herringbone pattern between antique beams. Golden Oak stain has mellowed to a rich patina that is a joy to live with.
If you have ceiling beams, run the panels perpendicular to beams for an interesting twist.

How Should Beadboard Run on a Cathedral Ceiling?
Taking into consideration the advice we've been offered by a number of experts, we've come to the conclusion that which way beadboard ceilings should run is really down to your tastes!
On a practical level, it's ideal to nail your beadboard to the joists. However, beyond this, it's up to you.
You can install beadboard ceiling panels in the same direction as your floor boards for visual continuity. If you have ceiling beams, run the panels perpendicular to beams for an interesting twist.
For a cathedral ceiling, the slope, ridge, beams, lighting, and room proportions should be considered together before cutting the panels. A clear layout plan is especially important because the sloping surfaces make seams and changes in direction more visible.
Tools and Materials
After you've psyched yourself up, you've got some prep work to do.
- Brad nailer with air compressor
- Brad Nails
- Finish nailer
- Finish Nails
- Drywall square
- Measuring tape obv.
- Compound miter saw
- Circular saw
- Jigsaw
- Ladder
- Glue
- Caulk gun
- Chalk box
- Tool belt
- Saw horses
- Beadboard panels
- Painter's Tool
- Three Piece Trim Removal Set
- 1x4s for trim
- Crown molding
- Cove molding
- Crown molding hanger
- Caulk
Preparation Before Installation
Remove Existing Trim and Fixtures
Before you get started, you'll need to pull down any existing crown molding or trimwork. If you plan on reusing the crown, be super careful pulling it off the wall / ceiling.
Also, don't forget to kill your breaker and remove any light fixtures in the room. Safety first, or at least early.
Locate the Ceiling Joists
If you're putting up the beadboard panels on a flat ceiling, I would grab your stud finder and locate your joists on opposite ends of your ceiling. Snap a chalkline to indicate where your joists are, and ideally you'd have a separate chalk color you can use for laying out your beadboard pattern.
For textured ceilings: If you're covering popcorn ceiling your studfinder isn't going to be much help locating your ceiling joists. If you have access to your attic, and it's not a complete wasteland, you might be able to get a long / thin drill bit through either side of the joists in your attic to indicate on the ceiling where your joists are.
If you can do this, mark your joists with a different colored chalk line than you plan to use for marking your beadboard layout.
If you don't have a way of marking your ceiling joists, it's ok. I didn't either. You'll just use a ton more nails.
Plan the Panel Layout
Let's layout our beadboard pattern! If you have overhead lighting in your room, you need to decide where you want your panel seams to be in relation to the light.
I think it looks better for the light to be in the center (or as much as possible) of a beadboard panel, but if your room is small or narrow, you may need to have the light on a seam.
Our living room and dining rooms are about 150sq ft so I opted for a 9 panel layout. The girls' bedroom is really narrow so I opted for a 6 panel layout in their room.
As I'm typing this out, it sounds crazy complicated, but truly, it's really simple to do in person! I've drawn a couple diagrams to help with my lack of explanation skills!
I would HIGHLY recommend you sketch out your room and draw your layout before getting started.
Planning a Nine-Panel Grid
First Pair of Grid Lines
For a 9 panel grid: Measure the length of WALL C in inches. Divide that number by 3 and write it down.
Measuring from WALL A, mark POINT 1 (closest to WALL C) and POINT 2 (closest to WALL D). The distance from WALL A to POINT 1 and POINT 2 is the length of WALL C divided by 3.
From WALL B, mark POINT 3 (closest to WALL C) and POINT 4 (closest to WALL D). Again, you're using the measurement of WALL C divided by 3.
Snap a chalkline connecting POINT 1 and POINT 2. Snap another line connecting POINT 3 and POINT 4.
At this point, you should have 2 chalk lines on your ceiling, and they should be the same distant from each other as they are from WALL A and WALL B. Check yourself before you wreck yourself!
Perpendicular Grid Lines
Follow the same steps to mark your grid lines perpendicular to the ones we've just marked.
Measure the length of WALL A in inches. Divide that number by 3 and write it down.
Measuring from WALL C, mark POINT 5 (closest to WALL A) and POINT 6 (closest to WALL B). The distance from WALL C to POINT 5 is the length of WALL A divided by 3.
From Wall D, mark POINT 7 (closest to WALL A) and POINT 8 (closest to WALL B). Again, you're using the measurement of WALL A divided by 3
Snap your chalkline connecting POINTS 5 and 6. Snap another line connecting POINT 7 and POINT 8.
At this point you should have a grid on your ceiling that looks somewhat similar to figure 2. Double check that all your lines are correct and let's move on.
Building a Deadman Brace
Last piece of prep-work, you need at least 1 deadman, preferably 2. A deadman brace is a couple pieces of scrap lumber assembled in the shape of a T to help you hold up your bead board panels.
Even if you have a helper with you, the deadman is indispensable. I used 2x6 common boards for this, but you could probably be just fine using 2x4s.
Just don't use pressure treated boards; they're too heavy!
For your long piece, measure the distance from the floor to the ceiling and subtract 1.5". Get another board and cut it to 36". Screw the center of the small board to the top of the long board, making a T.

Cutting the Beadboard Panels
The gridlines you snapped out are the borders for your bead board panels. They also will indicate where your 1x4 boards will be used to cover the seams.
If you've sketched on paper your ceiling layout, you should know the dimensions of each of your panels. If you didn't sketch out your ceiling, measure the dimensions of the squares on your ceiling and let's get cutting!
Take your bead board, measure your cutlines, and mark on the backside of the panel. I used a drywall square to draw my cutlines nice and straight.
Verify your measurement and make your first cut.
Start your panels in a corner of the room. When you make your first cut, make sure that the uncut edges (square edges) of the bead board panel will contact the 2 walls in the corner of your ceiling.
This will give you a greater chance of having the lines on the bead board parallel with your walls.
Installing Beadboard Panels on a Sloped Ceiling
Supporting the Panel
Prop one deadman against the wall so that the top of it is about 2-3 inches below the section of ceiling where you're about to hang the bead board.
Put your second deadman nearby so you can use it to prop up both ends of the bead board before you nail it in.
Get on your ladder and insert one edge of the bead board on top of your deadman. Adjust the panel so that it is square with your wall and pull the first deadman towards you so that it holds the panel snugly against the ceiling.
Make any needed adjustments to the panel and then pull your second deadman in place so the entire panel is supported by your deadman braces.
Nailing the Panel
If everything is nice and square, press the panel nice and tight agains the ceiling and nail it up using your finish nailer.
If you had the luxury of marking your ceiling joists, I'd nail those first, and then put "supporting" nails between the joists to reduce the chance of sagging.
If you don't know where your joists are I shot one nail into every other "lane" on the panel all down the panel.
I'm not kidding when I tell you I used 5,000 nails on a 900 sq ft house.
Using Adhesive
When I started, I was using glue on the back of each panel. If you are covering popcorn ceilings, I found that there really isn't a point in gluing the panels since the texture on the ceiling will prevent the majority of the panel from contacting the ceiling.
If you are installing the panels on a flat ceiling, I would go ahead and add glue for added security.
Thick, heavier wood panels will need to be nailed into the ceiling joists. Thinner panels can be stuck to the ceiling with adhesive (such as Gorilla Glue Heavy Duty Construction Adhesive from Amazon).
You’ll still need to use some finishing nails to hold these panels in place while the adhesive sets.
Installing Subsequent Panels
The next panel should be the one that continues the lines down the ceiling of the panel you just installed. I do this just to make sure my lines are nice and straight if you're looking at a straight line down the room.
Cut your next panel to the dimensions based on the grid you created on your ceiling.
Don't worry if the panel is a little small. You'll cover this with your 1x4s.
Just make sure it doesn't go over your chalk lines and make certain that the lines on the panel match your first panel and are as straight as possible.
Install it in the same way as described above.
Installing the Center Panel and Light Fixture Opening
You'll almost certainly need help to install the center panel of the room since there isn't a good place to prop up your deadman braces.
Also, if you have overhead lighting, you'll need to cut out a circle that fits your light fixture. Luckily since you have chalk marks on your ceiling, you'll know exactly where your light needs to be.
Measure on the ceiling to the center of the light box and determine the circumference of your fixture.
Using a pencil and string, scribe a circle on the good side of your bead board panel. Drill a 1/4" hole on the inside edge of your scribed circle, then finish cutting out the circle with your jigsaw.
Ensure the panel fits properly with your light box, and install as before, except now you have a friend helping you!
If any openings need to be made for light fixtures or ventilation ports, you can simply cut your beadboard ceiling panels using a sharp utility knife.
Installing 1x4 Trim Boards
I'll first install 1x4s around the footprint of the ceiling (do ceilings have footprints?). Installing these is a bit easier with help from a friend, but if you have no friends (lol!) your deadman will suffice.
Start with WALL A and WALL B. Cut your 1x4s about 1/8" - 1/4" LONGER than the length of the wall.
Start with the ends of the board and have those contacting the walls such that the center bows down towards the floor.
Force the center of the board up so that the board is wedged very snugly between the wall and the ceiling.
Use your framing nailer to fasten the board to the ceiling. Also, not a bad idea if you wanted to use a bit of glue on these.
Repeat the process for the boards that run lengthwise down the ceiling.
For the boards that run perpendicular to the boards you just installed, measure the distance between boards at your bead board seam lines.
Cut these as close as possible to the exact space you need. You can't cut these overside 'cause they're too small to force in place, but you still want a really snug fit.
Make sure everything is nice and square and nail 'em up.
At this point, you've got all your bead board up, and your 1x4 trim boards are up and covering your panel seam lines. This looks pretty darn good right!?
Adding Cove Molding Inside the Panels
This next part is optional, but we opted to install cove mold on the inside each of the square panels on our ceiling.
This not only helps to hide the joint of the 1x4 over the bead board panel, but it adds a really nice elegant touch to the overall look and feel!
Measure the inside dimensions of each of your squares. Cut your cove mold at a 45 degree angle such that either end is slanted "backwards" and the "tips" of the mold are the exact measurement you need.
Ensure each piece is a snug fit and nail this up with your brad nailer.
Measure and cut all 4 pieces at once (and mark what piece goes where on your 1x4) so you minimize the commute time between your project and your mitre saw!
Crown Molding and Finishing Trim
Now you've got your bead board panels, 1x4 trim boards, and cove mold installed!
Now let's hand crown molding. For this section, I'm not even going to attempt to explain crown molding.
There are several different methods of cutting crown, and I'm equally terrible at each!
Let's just say our crown molding is installed with equal parts cuss words and caulk!
I will say though, that I bought these crown molding hanging things off of Amazon, and they are literally a game changer!
Caulking, Priming, and Painting
Last step prior to paint: Caulk!
Now you get to fill in those 5,000+ nail holes with caulk. Enjoy.
You can simply add caulk to any gaps to elevate the look and make it look professional and refined. Then, prime, paint and enjoy.
Beadboard Cathedral Ceiling Inspiration
Any kind of wooden paneling is a good idea when it comes to achieving the much sought-after nautical chic aesthetic. However, beadboard has that clean, simple look that offers a no-fuss solution to boring bedroom ceilings.
Juxtaposing a rich, navy blue with some bright white beadboard is a great way to give a room some maritime charm. We love how Pine and Prospect Home have embraced this theme throughout the room with dark wooden furniture, white and navy bedding and freshly painted white woodwork.
This combination ensures brightness without compromising on coziness - perfect for those seeking with a beach house interior to decorate.
Whether you're tired of looking up at the same outdated and unsightly ceilings in your home, or looking to spruce up the interior of your business, beadboard ceiling panels can be a great choice.
Not only are they lightweight and easy-to-install, they’re also incredibly easy to clean and maintain, with great added benefits in the form of fire, water and pest-resistant qualities.
Beadboard ceiling panels come in a wide variety of stylish colors, patterns and textures, with options to suit just about any interior design choices.